Ford Fusion Manuals

Ford Fusion: Exterior Lighting / Turn Signal and Hazard Lamps. Diagnosis and Testing

Ford Fusion 2013–2020 Service Manual / Electrical / Lighting / Exterior Lighting / Turn Signal and Hazard Lamps. Diagnosis and Testing

DTC Chart: BCM

Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).


  BCM DTC Chart


DTC Description Action
B123A:11 Left Front Turn Indicator: Circuit Short to Ground
  • For halogen headlamps, GO to Pinpoint Test B
  • For LED headlamps, GO to Pinpoint Test C
B123A:15 Left Front Turn Indicator: Circuit Short to Battery or Open
  • For halogen headlamps, GO to Pinpoint Test B
  • For LED headlamps, GO to Pinpoint Test C
B123B:11 Right Front Turn Indicator: Circuit Short to Ground
  • For halogen headlamps, GO to Pinpoint Test B
  • For LED headlamps, GO to Pinpoint Test C
B123B:15 Right Front Turn Indicator: Circuit Short to Battery or Open
  • For halogen headlamps, GO to Pinpoint Test B
  • For LED headlamps, GO to Pinpoint Test C
B1247:11 Left Rear Turn Indicator: Circuit Short To Ground   GO to Pinpoint Test D
B1247:15 Left Rear Turn Indicator: Circuit Short To Battery or Open   GO to Pinpoint Test D
B1248:11 Right Rear Turn Indicator: Circuit Short To Ground   GO to Pinpoint Test D
B1248:15 Right Rear Turn Indicator: Circuit Short To Battery or Open   GO to Pinpoint Test D
B1265:01 Left Rear Turn Lamp Feedback: General Electrical Failure   GO to Pinpoint Test H
B1266:01 Right Rear Turn Lamp Feedback: General Electrical Failure   GO to Pinpoint Test H
B1497:01 Left Front Turn Lamp Feedback: General Electrical Failure   GO to Pinpoint Test G
B1498:01 Right Front Turn Lamp Feedback: General Electrical Failure   GO to Pinpoint Test G
B1D35:11 Hazard Switch: Circuit Short to Ground   GO to Pinpoint Test F
U1000:00 Solid State Driver Protection Actived -Driver Disabled: No Sub Type Information The module has temporarily disabled an output because an excessive current draw exists (such as a short to ground). The BCM cannot enable the output until the cause of the short is corrected. ADDRESS all other Diagnostic Trouble Codes (DTCs) first. After the cause of the concern is corrected, CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. For additional information on BCM Field Effect Transistor (FET) protection,
REFER to: Module Controlled Functions - System Operation and Component Description (419-10 Multifunction Electronic Modules, Description and Operation).
U3000:49 Control Module: Internal Electronic Failure The module has permanently disabled an output because an excessive current draw fault (such as a short to ground) has exceeded the limits that the BCM can withstand. The cause of the excessive current draw MUST be corrected before a new BCM is installed. ADDRESS all other Diagnostic Trouble Codes (DTCs) first. After the cause of the concern is corrected,
Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Click here to access Guided Routine (BCM).Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing Internet Explorer version 11 or greater is required to perform this Pinpoint Test.
For additional information on BCM Field Effect Transistor (FET) protection,
REFER to: Module Controlled Functions - System Operation and Component Description (419-10 Multifunction Electronic Modules, Description and Operation).

DTC Chart: DDM

Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).


  DDM DTC Chart


DTC Description Action
B1D06:11 Left Turn Indicator: Circuit Short To Ground   GO to Pinpoint Test E
B1D06:15 Left Turn Indicator: Circuit Short To Battery Or Open   GO to Pinpoint Test E

DTC Chart: PDM

Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).


  PDM DTC Chart


DTC Description Action
B1D07:11 Right Turn Indicator: Circuit Short To Ground   GO to Pinpoint Test E
B1D07:15 Right Turn Indicator: Circuit Short To Battery Or Open   GO to Pinpoint Test E

DTC Chart: SCCM

Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).


  SCCM DTC Chart


DTC Description Action
B1D36:09 Turn Indicator Switch: Component Failure INSTALL a new LH steering column multifunction switch.
REFER to: Steering Column Multifunction Switch LH (211-05 Steering Wheel and Column Electrical Components, Removal and Installation).
CLEAR the Diagnostic Trouble Codes (DTCs). Run the SCCM self-test. If the DTC returns, INSTALL a new SCCM.
REFER to: Steering Column Control Module (SCCM) (211-05 Steering Wheel and Column Electrical Components, Removal and Installation).

Symptom Chart(s)

Symptom Chart: Turn Signal and Hazard Lamps

Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).


  Symptom Chart


Condition Possible Sources Actions
A module does not respond to the scan tool
  • Fuse
  • Wiring, terminals or connectors
  • Module
 
REFER to: Communications Network (418-00 Module Communications Network, Diagnosis and Testing).
The turn signal function is inoperative Refer to the Pinpoint Test   GO to Pinpoint Test A
The turn signal function is always on
  • Multifunction switch
  • SCCM
INSTALL a new LH steering column multifunction switch.
REFER to: Steering Column Multifunction Switch LH (211-05 Steering Wheel and Column Electrical Components, Removal and Installation).
TEST the system for normal operation. If the concern still exists, INSTALL a new SCCM.
REFER to: Steering Column Control Module (SCCM) (211-05 Steering Wheel and Column Electrical Components, Removal and Installation).
One front turn signal lamp is inoperative or always on - halogen headlamps Refer to the Pinpoint Test   GO to Pinpoint Test B
One front turn signal lamp is inoperative or always on - LED headlamps Refer to the Pinpoint Test   GO to Pinpoint Test C
One rear turn signal lamp is inoperative or always on Refer to the Pinpoint Test   GO to Pinpoint Test D
One exterior mirror turn signal lamp is inoperative or always on Refer to the Pinpoint Test   GO to Pinpoint Test E
The front turn signal indicator flashes fast when no turn signal lamps are inoperative or does not flash fast when a turn signal lamp is inoperative - LED headlamps Refer to the Pinpoint Test   GO to Pinpoint Test G
The rear turn signal indicator flashes fast when no turn signal lamps are inoperative or does not flash fast when a turn signal lamp is inoperative Refer to the Pinpoint Test   GO to Pinpoint Test H
The hazard lamp function is inoperative or always on Refer to the Pinpoint Test   GO to Pinpoint Test F

Pinpoint Tests

The Turn Signal Function Is Inoperative


Refer to Wiring Diagrams Cell 90 for schematic and connector information.

Normal Operation and Fault Conditions


REFER to: Exterior Lighting - Overview (417-01 Exterior Lighting, Description and Operation).


REFER to: Exterior Lighting - System Operation and Component Description (417-01 Exterior Lighting, Description and Operation).

Possible Sources

  • Multifunction switch
  • SCCM

PINPOINT TEST A : THE TURN SIGNAL FUNCTION IS INOPERATIVE
A1 CHECK THE SCCM (STEERING COLUMN CONTROL MODULE) TURN SIGNAL PARAMETER IDENTIFICATIONS (PIDS)
  • Ignition ON.
  • Using a scan tool, view SCCM Parameter Identifications (PIDs).
  • Monitor the Turn signal Left Switch Input Status (TRN_SIG_SW_L) and Turn signal Right Switch Input Status (TRN_SIG_SW_R) while placing the LH steering column multifunction switch in the left and right turn positions.

Do the Parameter Identifications (PIDs) match the LH steering column multifunction switch position?
Yes GO to A2
No INSTALL a new LH steering column multifunction switch.
REFER to: Steering Column Multifunction Switch LH (211-05 Steering Wheel and Column Electrical Components, Removal and Installation).
TEST the system for normal operation. If the concern is still present, GO to A3

A2 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
  • Disconnect and inspect all BCM connectors.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the BCM connectors. Make sure they seat and latch correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern,
Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Click here to access Guided Routine (BCM).Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing Internet Explorer version 11 or greater is required to perform this Pinpoint Test.
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

A3 CHECK FOR CORRECT SCCM (STEERING COLUMN CONTROL MODULE) OPERATION
  • Disconnect and inspect all SCCM connectors.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the SCCM connectors. Make sure they seat and latch correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new SCCM
REFER to: Steering Column Control Module (SCCM) (211-05 Steering Wheel and Column Electrical Components, Removal and Installation).
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.


One Front Turn Signal Lamp Is Inoperative Or Always On - Halogen Headlamps


Refer to Wiring Diagrams Cell 90 for schematic and connector information.

Normal Operation and Fault Conditions


REFER to: Exterior Lighting - Overview (417-01 Exterior Lighting, Description and Operation).


REFER to: Exterior Lighting - System Operation and Component Description (417-01 Exterior Lighting, Description and Operation).


  DTC Fault Trigger Conditions


DTC Description Fault Trigger Conditions
B123A:11 Left Front Turn Indicator: Circuit Short To Ground A continuous memory and on-demand DTC that sets when the BCM detects a short to ground from the left front turn lamp voltage supply circuit.
B123A:15 Left Front Turn Indicator: Circuit Short To Battery Or Open A continuous memory and on-demand DTC that sets when the BCM detects an open or short to voltage from the left front turn lamp voltage supply circuit.
B123B:11 Right Front Turn Indicator: Circuit Short To Ground A continuous memory and on-demand DTC that sets when the BCM detects a short to ground from the right front turn lamp voltage supply circuit.
B123B:15 Right Front Turn Indicator: Circuit Short To Battery Or Open A continuous memory and on-demand DTC that sets when the BCM detects an open or short to voltage from the right front turn lamp voltage supply circuit.
U1000:00 Solid State Driver Protection Actived -Driver Disabled: No Sub Type Information This DTC sets when the BCM has temporarily shut down the output driver. The module has temporarily disabled an output because an excessive current draw exists (such as a short to ground). The BCM cannot enable the output until the cause of the short is corrected, the Diagnostic Trouble Codes (DTCs) have been cleared and a successful self-test is run. For additional information on BCM Field Effect Transistor (FET) protection,
REFER to: Module Controlled Functions - System Operation and Component Description (419-10 Multifunction Electronic Modules, Description and Operation).
U3000:49 Control Module: Internal Electronic Failure This DTC sets when the BCM has permanently shut down the output driver. The module has permanently disabled an output because an excessive current draw fault (such as a short to ground) has exceeded the limits that the BCM can withstand. CORRECT the cause of the excessive current draw before installing a new BCM. For additional information on BCM Field Effect Transistor (FET) protection,
REFER to: Module Controlled Functions - System Operation and Component Description (419-10 Multifunction Electronic Modules, Description and Operation).

Possible Sources

  • Bulb
  • Wiring, terminals or connectors
  • BCM

PINPOINT TEST B : ONE FRONT TURN SIGNAL LAMP IS INOPERATIVE OR ALWAYS ON - HALOGEN HEADLAMPS
B1 DETERMINE IF ANY TURN LAMP IS ALWAYS ON
  • Ignition ON.
  • Activate the hazard lamp function.
  • Observe the front and the rear turn lamps.

Is any turn lamp continuously illuminated?
Yes GO to B2
No GO to B3

B2 CHECK THE TURN LAMP VOLTAGE SUPPLY CIRCUIT FOR A SHORT TO VOLTAGE
  • Ignition OFF.
  • Disconnect: BCM C2280C.
  • Ignition ON.

Does the turn lamp in question continue to illuminate?
Yes REPAIR the affected circuit.
No GO to B8

B3 CHECK FOR VOLTAGE TO THE FRONT TURN LAMP
  • Ignition OFF.
  • Disconnect: LH Headlamp C1509A or RH Headlamp C1510A.
  • Ignition ON.
  • Activate the hazard flasher lamp function.
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1509A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1510A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Does the voltage alternate from 0 to greater than 11 volts?
Yes GO to B5
No GO to B4

B4 REPEAT THE ON-DEMAND SELF-TEST AND CHECK FOR VOLTAGE TO THE FRONT TURN LAMP
  • Deactivate the hazard flasher lamp function.
  • Using a diagnostic scan tool, perform the BCM self-test.
  • Clear the Diagnostic Trouble Codes (DTCs) and repeat the self-test (required to enable the lamp output driver).
  • Ignition OFF.
  • Ignition ON.
  • Activate the hazard flasher lamp function.
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1509A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1510A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Does the voltage alternate from 0 to greater than 11 volts?
Yes CHECK the internal headlamp harness for open or shorted circuits and damaged or pushed-out pins. If the harness is not OK, REPAIR the harness. If the harness is OK, INSTALL a new bulb. If the harness can not be repaired, INSTALL a new headlamp assembly.
REFER to: Headlamp Assembly (417-01 Exterior Lighting, Removal and Installation).
No GO to B6

B5 CHECK THE HEADLAMP GROUND CIRCUIT FOR AN OPEN
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1509A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C1509A-16

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1510A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C1510A-16

Does the voltage alternate from 0 to greater than 11 volts?
Yes CHECK the internal headlamp harness for open or shorted circuits and damaged or pushed-out pins. If the harness is not OK, REPAIR the harness. If the harness is OK, INSTALL a new bulb. If the harness can not be repaired, INSTALL a new headlamp assembly.
REFER to: Headlamp Assembly (417-01 Exterior Lighting, Removal and Installation).
No REPAIR the circuit.

B6 CHECK THE FRONT TURN LAMP SUPPLY CIRCUIT FOR A SHORT TO GROUND
  • Ignition OFF.
  • Deactivate the hazard flasher lamp function.
  • Disconnect: BCM C2280C.
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1509A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1510A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Is the resistance greater than 10,000 ohms?
Yes GO to B7
No REPAIR the circuit. After the repair:
If no Diagnostic Trouble Codes (DTCs) are present, TEST the system for normal operation.
If any BCM Diagnostic Trouble Codes (DTCs) other than DTC U3000:49 are present, CLEAR the Diagnostic Trouble Codes (DTCs), REPEAT the self-test (required to enable the lamp output driver) and cycle the ignition OFF and ON. TEST the system for normal operation.
If DTC U3000:49 is present,
Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Click here to access Guided Routine (BCM).Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing Internet Explorer version 11 or greater is required to perform this Pinpoint Test.

B7 CHECK THE FRONT TURN LAMP SUPPLY CIRCUIT FOR AN OPEN
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1509A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C2280C-39

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1510A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C2280C-38

Is the resistance less than 3 ohms?
Yes GO to B8
No REPAIR the circuit.

B8 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
  • Disconnect and inspect all BCM connectors.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the BCM connectors. Make sure they seat and latch correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern,
Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Click here to access Guided Routine (BCM).Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing Internet Explorer version 11 or greater is required to perform this Pinpoint Test.
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.


One Front Turn Signal Lamp Is Inoperative Or Always On - LED headlamps


Refer to Wiring Diagrams Cell 90 for schematic and connector information.

Normal Operation and Fault Conditions


REFER to: Exterior Lighting - Overview (417-01 Exterior Lighting, Description and Operation).


REFER to: Exterior Lighting - System Operation and Component Description (417-01 Exterior Lighting, Description and Operation).


  DTC Fault Trigger Conditions


DTC Description Fault Trigger Conditions
B123A:11 Left Front Turn Indicator: Circuit Short To Ground A continuous memory and on-demand DTC that sets when the BCM detects a short to ground from the left front turn lamp voltage supply circuit.
B123A:15 Left Front Turn Indicator: Circuit Short To Battery Or Open A continuous memory and on-demand DTC that sets when the BCM detects an open or short to voltage from the left front turn lamp voltage supply circuit.
B123B:11 Right Front Turn Indicator: Circuit Short To Ground A continuous memory and on-demand DTC that sets when the BCM detects a short to ground from the right front turn lamp voltage supply circuit.
B123B:15 Right Front Turn Indicator: Circuit Short To Battery Or Open A continuous memory and on-demand DTC that sets when the BCM detects an open or short to voltage from the right front turn lamp voltage supply circuit.
B1497:01 Left Front Turn Lamp Feedback: General Electrical Failure A continuous memory DTC that sets when the BCM detects an electrical failure from the LH front turn lamp outage circuit when the turn lamp is activated.
B1498:01 Right Front Turn Lamp Feedback: General Electrical Failure A continuous memory DTC that sets when the BCM detects an electrical failure from the RH front turn lamp outage circuit when the turn lamp is activated.
U1000:00 Solid State Driver Protection Actived -Driver Disabled: No Sub Type Information This DTC sets when the BCM has temporarily shut down the output driver. The module has temporarily disabled an output because an excessive current draw exists (such as a short to ground). The BCM cannot enable the output until the cause of the short is corrected, the Diagnostic Trouble Codes (DTCs) have been cleared and a successful self-test is run. For additional information on BCM Field Effect Transistor (FET) protection,
REFER to: Module Controlled Functions - System Operation and Component Description (419-10 Multifunction Electronic Modules, Description and Operation).
U3000:49 Control Module: Internal Electronic Failure This DTC sets when the BCM has permanently shut down the output driver. The module has permanently disabled an output because an excessive current draw fault (such as a short to ground) has exceeded the limits that the BCM can withstand. CORRECT the cause of the excessive current draw before installing a new BCM. For additional information on BCM Field Effect Transistor (FET) protection,
REFER to: Module Controlled Functions - System Operation and Component Description (419-10 Multifunction Electronic Modules, Description and Operation).

Possible Sources

  • Headlamp Assembly
  • Wiring, terminals or connectors
  • BCM
  • Adaptive front lighting module

PINPOINT TEST C : ONE FRONT TURN SIGNAL LAMP IS INOPERATIVE OR ALWAYS ON - LED (LIGHT EMITTING DIODE) HEADLAMPS
C1 DETERMINE IF ANY TURN LAMP IS ALWAYS ON
  • Ignition ON.
  • Activate the hazard lamp function.
  • Observe the front and the rear turn lamps.

Is any turn lamp continuously illuminated?
Yes GO to C2
No GO to C4

C2 CHECK THE TURN LAMP VOLTAGE SUPPLY CIRCUIT FOR VOLTAGE
  • Ignition OFF.
  • Disconnect: LH Headlamp C1509A or RH Headlamp C1510A.
  • Ignition ON.
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1509A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1510A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Is any voltage present?
Yes GO to C3
No GO to C9

C3 CHECK THE TURN LAMP VOLTAGE SUPPLY CIRCUIT FOR A SHORT TO VOLTAGE
  • Ignition OFF.
  • Disconnect: BCM C2280C.
  • Ignition ON.
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1509A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1510A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Is any voltage present?
Yes REPAIR the affected circuit.
No GO to C10

C4 CHECK FOR VOLTAGE TO THE FRONT TURN LAMP
  • Ignition OFF.
  • Disconnect: LH Headlamp C1509A or RH Headlamp C1510A.
  • Ignition ON.
  • Activate the hazard flasher lamp function.
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1509A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1510A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Does the voltage alternate from 0 to greater than 11 volts?
Yes GO to C6
No GO to C5

C5 REPEAT THE ON-DEMAND SELF-TEST AND CHECK FOR VOLTAGE TO THE FRONT TURN LAMP
  • Deactivate the hazard flasher lamp function.
  • Using a diagnostic scan tool, perform the BCM self-test.
  • Clear the Diagnostic Trouble Codes (DTCs) and repeat the self-test (required to enable the lamp output driver).
  • Ignition OFF.
  • Ignition ON.
  • Activate the hazard flasher lamp function.
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1509A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1510A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Does the voltage alternate from 0 to greater than 11 volts?
Yes GO to C9
No GO to C7

C6 CHECK THE HEADLAMP GROUND CIRCUIT FOR AN OPEN
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1509A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C1509A-16

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1510A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C1510A-16

Does the voltage alternate from 0 to greater than 11 volts?
Yes GO to C9
No REPAIR the circuit.

C7 CHECK THE FRONT TURN LAMP SUPPLY CIRCUIT FOR A SHORT TO GROUND
  • Ignition OFF.
  • Deactivate the hazard flasher lamp function.
  • Disconnect: BCM C2280C.
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1509A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1510A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Is the resistance greater than 10,000 ohms?
Yes GO to C8
No REPAIR the circuit. After the repair:
If no Diagnostic Trouble Codes (DTCs) are present, TEST the system for normal operation.
If any BCM Diagnostic Trouble Codes (DTCs) other than DTC U3000:49 are present, CLEAR the Diagnostic Trouble Codes (DTCs), REPEAT the self-test (required to enable the lamp output driver) and cycle the ignition OFF and ON. TEST the system for normal operation.
If DTC U3000:49 is present,
Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Click here to access Guided Routine (BCM).Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing Internet Explorer version 11 or greater is required to perform this Pinpoint Test.

C8 CHECK THE FRONT TURN LAMP SUPPLY CIRCUIT FOR AN OPEN
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1509A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C2280C-39

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1510A-7 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C2280C-38

Is the resistance less than 3 ohms?
Yes GO to C10
No REPAIR the circuit.

C9 CHECK THE ADAPTIVE FRONT LIGHTING MODULE
  • Remove the suspect adaptive front lighting module.
  • Substitute the known good adaptive front lighting module from the opposite headlamp.
  • Clear the Diagnostic Trouble Codes (DTCs), Repeat the self-test (required to enable the lamp output driver) and cycle the ignition OFF and ON. Test the system for normal operation.

Does the suspect headlamp operate?
Yes REMOVE the known good adaptive front lighting module. INSTALL a new adaptive front lighting module.
No REMOVE the known good adaptive front lighting module. INSTALL a new headlamp assembly. INSTALL a new headlamp assembly.
REFER to: Headlamp Assembly (417-01 Exterior Lighting, Removal and Installation).

C10 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
  • Disconnect and inspect all BCM connectors.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the BCM connectors. Make sure they seat and latch correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern,
Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Click here to access Guided Routine (BCM).Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing Internet Explorer version 11 or greater is required to perform this Pinpoint Test.
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.


One Rear Turn Signal Lamp Is Inoperative Or Always On


Refer to Wiring Diagrams Cell 90 for schematic and connector information.

Normal Operation and Fault Conditions


REFER to: Exterior Lighting - Overview (417-01 Exterior Lighting, Description and Operation).


REFER to: Exterior Lighting - System Operation and Component Description (417-01 Exterior Lighting, Description and Operation).


  DTC Fault Trigger Conditions


DTC Description Fault Trigger Conditions
B1247:11 Left Rear Turn Indicator: Circuit Short To Ground A continuous memory DTC that sets when the BCM detects a short to ground from the left rear turn lamp voltage supply circuit.
B1247:15 Left Rear Turn Indicator: Circuit Short To Battery or Open A continuous memory DTC that sets when the BCM detects an open or short to voltage from the left rear turn lamp voltage supply circuit.
B1248:11 Right Rear Turn Indicator: Circuit Short To Ground A continuous memory DTC that sets when the BCM detects a short to ground from the right rear turn lamp voltage supply circuit.
B1248:15 Right Rear Turn Indicator: Circuit Short To Battery or Open A continuous memory DTC that sets when the BCM detects an open or short to voltage from the right rear turn lamp voltage supply circuit.
U1000:00 Solid State Driver Protection Actived -Driver Disabled: No Sub Type Information This DTC sets when the BCM has temporarily shut down the output driver. The module has temporarily disabled an output because an excessive current draw exists (such as a short to ground). The BCM cannot enable the output until the cause of the short is corrected, the Diagnostic Trouble Codes (DTCs) have been cleared and a successful self-test is run. For additional information on BCM Field Effect Transistor (FET) protection,
REFER to: Module Controlled Functions - System Operation and Component Description (419-10 Multifunction Electronic Modules, Description and Operation).
U3000:49 Control Module: Internal Electronic Failure This DTC sets when the BCM has permanently shut down the output driver. The module has permanently disabled an output because an excessive current draw fault (such as a short to ground) has exceeded the limits that the BCM can withstand. CORRECT the cause of the excessive current draw before installing a new BCM. For additional information on BCM Field Effect Transistor (FET) protection,
REFER to: Module Controlled Functions - System Operation and Component Description (419-10 Multifunction Electronic Modules, Description and Operation).

Possible Sources

  • Rear lamp assembly
  • Wiring, terminals or connectors
  • BCM

PINPOINT TEST D : ONE REAR TURN SIGNAL LAMP IS INOPERATIVE OR ALWAYS ON
D1 DETERMINE IF ANY REAR TURN LAMP IS ALWAYS ON
  • Ignition ON.
  • Activate the hazard lamp function.
  • Observe the rear turn lamps.

Is any turn lamp continuously illuminated?
Yes GO to D2
No GO to D3

D2 CHECK THE TURN LAMP VOLTAGE SUPPLY CIRCUIT FOR A SHORT TO VOLTAGE
  • Ignition OFF.
  • Disconnect: BCM C2280D.
  • Ignition ON.

Does the turn lamp in question continue to illuminate?
Yes REPAIR the affected circuit.
No GO to D8

D3 CHECK FOR VOLTAGE TO THE REAR TURN LAMP
  • Ignition OFF.
  • Disconnect: LH Rear Lamp C412 or RH Rear Lamp C415.
  • Ignition ON.
  • Activate the hazard flasher lamp function.
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C412-3 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C415-3 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Does the voltage alternate from 0 to greater than 11 volts?
Yes GO to D5
No GO to D4

D4 REPEAT THE ON-DEMAND SELF-TEST AND CHECK FOR VOLTAGE TO THE REAR TURN LAMP
  • Deactivate the hazard flasher lamp function.
  • Using a diagnostic scan tool, perform the BCM self-test.
  • Clear the Diagnostic Trouble Codes (DTCs) and repeat the self-test (required to enable the lamp output driver).
  • Ignition OFF.
  • Ignition ON.
  • Activate the hazard flasher lamp function.
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C412-3 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C415-3 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Does the voltage alternate from 0 to greater than 11 volts?
Yes INSTALL a new rear lamp assembly.
REFER to: Rear Lamp Assembly - 4-Door (417-01 Exterior Lighting, Removal and Installation).
No GO to D6

D5 CHECK THE REAR LAMP GROUND CIRCUIT FOR AN OPEN
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C412-3 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C412-4

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C415-3 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C415-4

Does the voltage alternate from 0 to greater than 11 volts?
Yes INSTALL a new rear lamp assembly.
REFER to: Rear Lamp Assembly - 4-Door (417-01 Exterior Lighting, Removal and Installation).
No REPAIR the circuit.

D6 CHECK THE REAR TURN LAMP SUPPLY CIRCUIT FOR A SHORT TO GROUND
  • Ignition OFF.
  • Deactivate the hazard flasher lamp function.
  • Disconnect: BCM C2280D.
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C412-3 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C415-3 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Is the resistance greater than 10,000 ohms?
Yes GO to D7
No REPAIR the circuit. After the repair:
If no Diagnostic Trouble Codes (DTCs) are present, TEST the system for normal operation.
If any BCM Diagnostic Trouble Codes (DTCs) other than DTC U3000:49 are present, CLEAR the Diagnostic Trouble Codes (DTCs), REPEAT the self-test (required to enable the lamp output driver) and cycle the ignition OFF and ON. TEST the system for normal operation.
If DTC U3000:49 is present,
Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Click here to access Guided Routine (BCM).Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing Internet Explorer version 11 or greater is required to perform this Pinpoint Test.

D7 CHECK THE REAR TURN LAMP SUPPLY CIRCUIT FOR AN OPEN
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C412-3 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C2280D-26

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C415-3 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C2280D-52

Is the resistance less than 3 ohms?
Yes GO to D8
No REPAIR the circuit.

D8 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
  • Disconnect and inspect all BCM connectors.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the BCM connectors. Make sure they seat and latch correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern,
Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Click here to access Guided Routine (BCM).Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing Internet Explorer version 11 or greater is required to perform this Pinpoint Test.
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.


One Exterior Mirror Turn Signal Lamp Is Inoperative Or Always On


Refer to Wiring Diagrams Cell 90 for schematic and connector information.

Normal Operation and Fault Conditions


REFER to: Exterior Lighting - Overview (417-01 Exterior Lighting, Description and Operation).


REFER to: Exterior Lighting - System Operation and Component Description (417-01 Exterior Lighting, Description and Operation).


  DTC Fault Trigger Conditions


DTC Description Fault Trigger Conditions
B1D06:11 Left Turn Indicator: Circuit Short To Ground A continuous memory DTC that sets when the DDM detects an open or short to voltage from the exterior mirror turn lamp voltage supply circuit.
B1D06:15 Left Turn Indicator: Circuit Short To Battery Or Open A continuous memory DTC that sets when the DDM detects an open or short to voltage from the exterior mirror turn lamp voltage supply circuit.
B1D07:11 Right Turn Indicator: Circuit Short To Ground A continuous memory DTC that sets when the PDM detects an open or short to voltage from the exterior mirror turn lamp voltage supply circuit.
B1D07:15 Right Turn Indicator: Circuit Short To Battery Or Open A continuous memory DTC that sets when the PDM detects an open or short to voltage from the exterior mirror turn lamp voltage supply circuit.

Possible Sources

  • Wiring, terminals or connectors
  • Exterior mirror
  • DDM
  • PDM

PINPOINT TEST E : ONE EXTERIOR MIRROR TURN SIGNAL LAMP IS INOPERATIVE OR ALWAYS ON
E1 DETERMINE IF EITHER EXTERIOR MIRROR TURN LAMP IS ALWAYS ON
  • Ignition ON.
  • Activate the hazard lamp function.
  • Observe the exterior mirror turn lamps.

Is any exterior mirror turn lamp continuously illuminated?
Yes GO to E2
No GO to E3

E2 CHECK THE TURN LAMP VOLTAGE SUPPLY CIRCUIT FOR A SHORT TO VOLTAGE
  • Ignition OFF.
  • Disconnect: DDM C501A (LH exterior mirror lamp).
  • Disconnect: PDM C652A ( RH exterior mirror lamp).
  • Ignition ON.

Does the turn lamp in question continue to illuminate?
Yes REPAIR the affected circuit.
No For the LH exterior mirror turn lamp, GO to E7
For the RH exterior mirror turn lamp, GO to E8

E3 CHECK FOR VOLTAGE TO THE EXTERIOR MIRROR
  • Ignition OFF.
  • Disconnect: LH Exterior Mirror C517 or RH Exterior Mirror C626.
  • Ignition ON.
  • Activate the hazard flasher lamp function.
  • Measure:
    Click to display connectors

      LH Exterior Mirror Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C517-10 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Exterior Mirror Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C626-10 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Does the voltage alternate from 0 to greater than 11 volts?
Yes GO to E4
No GO to E5

E4 CHECK THE EXTERIOR MIRROR TURN LAMP GROUND
  • Measure:
    Click to display connectors

      LH Exterior Mirror Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C517-10 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C517-8

    Click to display connectors

      RH Exterior Mirror Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C626-10 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C626-8

Does the voltage alternate from 0 to greater than 11 volts?
Yes INSTALL a new exterior mirror.
REFER to: Exterior Mirror (501-09 Rear View Mirrors, Removal and Installation).
No REPAIR the circuit.

E5 CHECK THE EXTERIOR MIRROR TURN LAMP SUPPLY CIRCUIT FOR A SHORT TO GROUND
  • Ignition OFF.
  • Deactivate the hazard flasher lamp function.
  • Disconnect: DDM C501A (LH exterior mirror lamp).
  • Disconnect: PDM C652A (RH exterior mirror lamp).
  • Measure:
    Click to display connectors

      LH Exterior Mirror Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C517-10 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Exterior Mirror Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C626-10 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Is the resistance greater than 10,000 ohms?
Yes GO to E6
No REPAIR the circuit.

E6 CHECK THE MIRROR TURN LAMP SUPPLY CIRCUIT FOR AN OPEN
  • Measure:
    Click to display connectors

      LH Exterior Mirror Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C517-10 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C501A-4

    Click to display connectors

      RH Exterior Mirror Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C626-10 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C652A-4

Is the resistance less than 3 ohms?
Yes For the LH exterior mirror turn lamp, GO to E7
For the RH exterior mirror turn lamp, GO to E8
No REPAIR the circuit.

E7 CHECK FOR CORRECT DDM (DRIVER DOOR MODULE) OPERATION
  • Disconnect and inspect all DDM connectors.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the DDM connectors. Make sure they seat and latch correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new DDM.
REFER to: Driver Door Module (DDM) (419-10 Multifunction Electronic Modules, Removal and Installation).
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

E8 CHECK FOR CORRECT PDM (PASSENGER DOOR MODULE) OPERATION
  • Disconnect and inspect all PDM connectors.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the PDM connectors. Make sure they seat and latch correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new PDM.
REFER to: Passenger Door Module (PDM) (419-10 Multifunction Electronic Modules, Removal and Installation).
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.


The Hazard Lamp Function Is Inoperative Or Always On


Refer to Wiring Diagrams Cell 90 for schematic and connector information.

Normal Operation and Fault Conditions


REFER to: Exterior Lighting - Overview (417-01 Exterior Lighting, Description and Operation).


REFER to: Exterior Lighting - System Operation and Component Description (417-01 Exterior Lighting, Description and Operation).


  DTC Fault Trigger Conditions


DTC Description Fault Trigger Conditions
B1D35:11 Hazard Switch: Circuit Short to Ground A continuous memory and on-demand DTC that sets when the BCM detects a short to ground from the hazard lamp function input circuit.
U1000:00 Solid State Driver Protection Actived -Driver Disabled: No Sub Type Information This DTC sets when the BCM has temporarily shut down the output driver. The module has temporarily disabled an output because an excessive current draw exists (such as a short to ground). The BCM cannot enable the output until the cause of the short is corrected, the Diagnostic Trouble Codes (DTCs) have been cleared and a successful self-test is run.
U3000:49 Control Module: Internal Electronic Failure This DTC sets when the BCM has permanently shut down the output driver. The module has permanently disabled an output because an excessive current draw fault (such as a short to ground) has exceeded the limits that the BCM can withstand. CORRECT the cause of the excessive current draw before installing a new BCM.

Possible Sources

  • Wiring, terminals or connectors
  • Hazard Flasher Switch
  • BCM

PINPOINT TEST F : THE HAZARD LAMP FUNCTION IS INOPERATIVE OR ALWAYS ON
F1 CHECK FOR BCM (BODY CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
  • Ignition ON.
  • Using a scan tool, perform the BCM self-test.

Is DTC B1D35:11 present?
Yes GO to F2
No GO to F4

F2 ISOLATE THE HAZARD FLASHER SWITCH
  • Ignition OFF.
  • Disconnect: Hazard Flasher Switch C2480.
  • Ignition ON.
  • Using a scan tool, clear the Diagnostic Trouble Codes (DTCs) and repeat the BCM self-test.

Is DTC B1D35:11 retrieved again?
Yes GO to F3
No GO to F6

F3 CHECK THE HAZARD FLASHER SWITCH INPUT CIRCUIT FOR A SHORT TO GROUND
  • Ignition OFF.
  • Disconnect: BCM C2280G.
  • Measure:
    Click to display connectors
    Positive Lead Measurement / Action Negative Lead
      C2480-3 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Is the resistance greater than 10,000 ohms?
Yes GO to F7
No REPAIR the circuit.

F4 CHECK FOR A VOLTAGE SIGNAL TO THE HAZARD FLASHER SWITCH
  • Ignition OFF.
  • Disconnect: Hazard Flasher Switch C2480.
  • Ignition ON.
  • Measure:
    Click to display connectors
    Positive Lead Measurement / Action Negative Lead
      C2480-3 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Is the voltage greater than 11 volts?
Yes GO to F5
No GO to F6

F5 CHECK THE HAZARD FLASHER SWITCH GROUND CIRCUIT FOR AN OPEN
  • Measure:
    Click to display connectors
    Positive Lead Measurement / Action Negative Lead
      C2480-3 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C2480-1

Is the voltage greater than 11 volts?
Yes INSTALL a new hazard flasher switch.
REFER to: Hazard Flasher Switch (417-01 Exterior Lighting, Removal and Installation).
No REPAIR the circuit.

F6 CHECK THE HAZARD FLASHER SWITCH INPUT CIRCUIT FOR AN OPEN
  • Ignition OFF.
  • Disconnect: BCM C2280G.
  • Measure:
    Click to display connectors
    Positive Lead Measurement / Action Negative Lead
      C2480-3 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C2280G-19

Is the resistance less than 3 ohms?
Yes GO to F7
No REPAIR the circuit.

F7 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
  • Disconnect and inspect all BCM connectors.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the BCM connectors. Make sure they seat and latch correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern,
Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Click here to access Guided Routine (BCM).Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing Internet Explorer version 11 or greater is required to perform this Pinpoint Test.
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.


The Front Turn Signal Indicator Flashes Fast When No Turn Signal Lamps Are Inoperative Or Does Not Flash Fast When A Turn Signal Lamp Is Inoperative - LED Headlamps


Refer to Wiring Diagrams Cell 90 for schematic and connector information.

Normal Operation and Fault Conditions


REFER to: Exterior Lighting - Overview (417-01 Exterior Lighting, Description and Operation).


REFER to: Exterior Lighting - System Operation and Component Description (417-01 Exterior Lighting, Description and Operation).


  DTC Fault Trigger Conditions


DTC Description Fault Trigger Conditions
B1497:01 Left Front Turn Lamp Feedback: General Electrical Failure A continuous memory DTC that sets when the BCM detects an electrical failure from the LH rear turn lamp outage circuit when the turn lamp is activated.
B1498:01 Right Front Turn Lamp Feedback: General Electrical Failure A continuous memory DTC that sets when the BCM detects an electrical failure from the RH rear turn lamp outage circuit when the turn lamp is activated.

Possible Sources

  • Headlamp assembly
  • Wiring, terminals or connectors
  • BCM

PINPOINT TEST G : THE FRONT TURN SIGNAL INDICATOR FLASHES FAST WHEN NO TURN SIGNAL LAMPS ARE INOPERATIVE OR DOES NOT FLASH FAST WHEN A TURN SIGNAL LAMP IS INOPERATIVE - LED (LIGHT EMITTING DIODE) HEADLAMPS
G1 DETERMINE IF A TURN LAMP IS INOPERATIVE
  • Ignition ON.
  • While observing the front rear turn lamps, place the LH steering column multifunction switch in the left and right turn positions.

Is any turn lamp inoperative?
Yes GO to G2
No GO to G4

G2 CHECK THE FRONT TURN LAMP
  • Ignition OFF.
  • Disconnect: LH Headlamp C1509A or RH Headlamp C1510A.
  • Ignition ON.
  • While observing the front and the rear turn lamps, place the LH steering column multifunction switch in the inoperative turn position.

Does the turn signal indicator flash fast?
Yes GO to G7
No GO to G3

G3 CHECK THE FRONT TURN LAMP OUTAGE CIRCUIT FOR A SHORT TO VOLTAGE
  • Ignition OFF.
  • Disconnect: BCM C2280C.
  • Ignition ON.
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1509A-11 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1510A-11 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Is any voltage present?
Yes REPAIR the circuit.
No GO to G7

G4 CHECK THE FRONT TURN LAMP OUTAGE CIRCUIT FOR A SHORT TO GROUND
  • Ignition OFF.
  • Disconnect: LH Headlamp C1509A or RH Headlamp C1510A.
  • Disconnect: BCM C2280C.
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1509A-11 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1510A-11 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Is the resistance greater than 10,000 ohms?
Yes GO to G5
No REPAIR the circuit.

G5 CHECK THE FRONT TURN LAMP OUTAGE CIRCUIT FOR AN OPEN
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1509A-11 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C2280C-6

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C1510A-11 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C2280C-17

Is the resistance less than 3 ohms?
Yes GO to G6
No REPAIR the circuit.

G6 CHECK THE ADAPTIVE FRONT LIGHTING MODULE
  • REMOVE the suspect adaptive front lighting module.
  • Substitute the known good adaptive front lighting module from the opposite headlamp.
  • CLEAR the Diagnostic Trouble Codes (DTCs), REPEAT the self-test (required to enable the lamp output driver) and cycle the ignition OFF and ON. TEST the system for normal operation.

Does the suspect headlamp operate?
Yes REMOVE the known good adaptive front lighting module. INSTALL a new adaptive front lighting module.
No REMOVE the known good adaptive front lighting module. INSTALL a new headlamp assembly. INSTALL a new headlamp assembly.
REFER to: Headlamp Assembly (417-01 Exterior Lighting, Removal and Installation).

G7 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
  • Disconnect and inspect all BCM connectors.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the BCM connectors. Make sure they seat and latch correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern,
Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Click here to access Guided Routine (BCM).Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing Internet Explorer version 11 or greater is required to perform this Pinpoint Test.
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.


The Rear Turn Signal Indicator Flashes Fast When No Turn Signal Lamps Are Inoperative Or Does Not Flash Fast When A Turn Signal Lamp Is Inoperative


Refer to Wiring Diagrams Cell 90 for schematic and connector information.

Normal Operation and Fault Conditions


REFER to: Exterior Lighting - Overview (417-01 Exterior Lighting, Description and Operation).


REFER to: Exterior Lighting - System Operation and Component Description (417-01 Exterior Lighting, Description and Operation).


  DTC Fault Trigger Conditions


DTC Description Fault Trigger Conditions
B1265:01 Left Rear Turn Lamp Feedback: General Electrical Failure A continuous memory DTC that sets when the BCM detects an electrical failure from the LH rear turn lamp outage circuit when the turn lamp is activated.
B1266:01 Right Rear Turn Lamp Feedback: General Electrical Failure A continuous memory DTC that sets when the BCM detects an electrical failure from the RH rear turn lamp outage circuit when the turn lamp is activated.

Possible Sources

  • Rear lamp assembly
  • Wiring, terminals or connectors
  • BCM

PINPOINT TEST H : THE REAR TURN SIGNAL INDICATOR FLASHES FAST WHEN NO TURN SIGNAL LAMPS ARE INOPERATIVE OR DOES NOT FLASH FAST WHEN A TURN SIGNAL LAMP IS INOPERATIVE
H1 DETERMINE IF A TURN LAMP IS INOPERATIVE
  • Ignition ON.
  • While observing the rear turn lamps, place the LH steering column multifunction switch in the left and right turn positions.

Is any turn lamp inoperative?
Yes GO to H2
No GO to H3

H2 CHECK THE REAR TURN LAMP OUTAGE CIRCUIT FOR A SHORT TO VOLTAGE
  • Ignition OFF.
  • Disconnect: Inoperative LH Rear Lamp C412 or RH Rear Lamp C415.
  • Disconnect: BCM C2280D.
  • Ignition ON.
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C412-5 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C415-5 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Is any voltage present?
Yes REPAIR the circuit.
No GO to H5

H3 CHECK THE REAR TURN LAMP OUTAGE CIRCUIT FOR A SHORT TO GROUND
  • Ignition OFF.
  • Disconnect: Inoperative LH Rear Lamp C412 or RH Rear Lamp C415.
  • Disconnect: BCM C2280D.
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C412-5 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C415-5 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Ground

Is the resistance greater than 10,000 ohms?
Yes GO to H4
No REPAIR the circuit.

H4 CHECK THE REAR TURN LAMP OUTAGE CIRCUIT FOR AN OPEN
  • Measure:
    Click to display connectors

      LH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C412-5 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C2280D-31

    Click to display connectors

      RH Turn Lamp


    Positive Lead Measurement / Action Negative Lead
      C415-5 Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   C2280D-44

Is the resistance less than 3 ohms?
Yes INSTALL a new rear lamp assembly.
REFER to: Rear Lamp Assembly - 4-Door (417-01 Exterior Lighting, Removal and Installation).
If the turn lamp is still inoperative, GO to H5
No REPAIR the circuit.

H5 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
  • Disconnect and inspect all BCM connectors.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the BCM connectors. Make sure they seat and latch correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern,
Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing   Click here to access Guided Routine (BCM).Ford Fusion. Turn Signal and Hazard Lamps. Diagnosis and Testing Internet Explorer version 11 or greater is required to perform this Pinpoint Test.
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.


    Stoplamps. Diagnosis and Testing

    DTC Chart: BCM Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation)...

    Front Fog Lamp Adjustment. General Procedures

    Activation NOTE: Horizontal aim is not required for this vehicle and is not adjustable. Consult your state vehicle inspection center for recommended tolerance ranges for visual aiming...

    Other information:

    Ford Fusion 2013–2020 Service Manual: Electronic Engine Controls. Diagnosis and Testing


    DTC Chart: Powertrain Control Module (PCM) Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).   Powertrain Control Module (PCM) DTC Chart DTC Description Action P0125 Insufficient C..

    Ford Fusion 2013–2020 Owners Manual: Tire Pressure Monitoring System


    WARNING: The tire pressure monitoring system is not a substitute for manually checking tire pressures. You should periodically check tire pressures using a pressure gauge. Failure to correctly maintain tire pressures could increase the risk of tire failure, loss of control, vehicle rollover and personal injury. Note: You should only use tire sealants in roadside emergencies as they could ..

    Categories

    Direction Indicators. Interior Lamps

    Direction Indicators

    Ford Fusion. Direction Indicators. Interior Lamps

    Push the lever up or down to use the direction indicators.

    read more

    Copyright © 2024 www.fofusion2.com