Ford Fusion Manuals

Ford Fusion: Supplemental Restraint System / Supplemental Restraint System (SRS) Depowering and Repowering. General Procedures

Ford Fusion 2013–2020 Service Manual / Body and Paint / Body and Paint / Supplemental Restraint System / Supplemental Restraint System (SRS) Depowering and Repowering. General Procedures

Depower

  1. Ford Fusion. Supplemental Restraint System (SRS) Depowering and Repowering. General Procedures  WARNING: Before beginning any service procedure in this section, refer to Safety Warnings in section 100-00 General Information. Failure to follow this instruction may result in serious personal injury.

    NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.

    Refer to: Health and Safety Precautions (100-00 General Information, Description and Operation).
  1. Turn the ignition OFF.
  1. At the BCM, located under the instrument panel, to the left of the steering column, remove BECM fuse 14 (10A) and 35 (5A) from the BCM. Refer to Wiring Cell 11 Fuse and Relay Information for schematic and connector information.
  1. Turn the ignition ON and monitor the airbag warning indicator for at least 30 seconds. The airbag warning indicator remains lit continuously (no flashing) if the correct RCM fuse is removed. If the airbag warning indicator is not lit continuously, remove the correct fuses before proceding.
  1. Turn the ignition OFF.
  1. Disconnect the battery.
    Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
  1. Wait at least one minute before continuing vehicle service.

Repower

  1. Ford Fusion. Supplemental Restraint System (SRS) Depowering and Repowering. General Procedures  WARNING: Before beginning any service procedure in this section, refer to Safety Warnings in section 100-00 General Information. Failure to follow this instruction may result in serious personal injury.

    NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.

    Refer to: Health and Safety Precautions (100-00 General Information, Description and Operation).
  1. Install BECM fuses 14 (10A) and 35 (5A) in the BCM.
  1. Connect the battery.
    Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
  1. Sit in the driver seat in an upright position. Make sure no objects are between you and the driver airbag, driver knee airbag, side airbag or side air curtain.
    Dimension: 10.0  in ( 25.4  cm)
  1. Move the driver seat to the rearmost position.
  1. Turn the ignition from OFF to ON.
    • Prove out the SRS as follows: Turn the ignition from ON to OFF. Wait 10 seconds, then turn the ignition back to ON and monitor the airbag warning indicator with the airbag modules installed. The airbag warning indicator illuminates continuously for approximately 6 seconds and then turns off. If a SRS fault is present, the airbag warning indicator either fails to light, remains lit continuously or flashes.
    • The flashing may not occur until approximately 30 seconds after the ignition has been turned from OFF to ON. This is the time required for the RCM to complete the testing of the SRS. If the airbag warning indicator is inoperative and a SRS fault exists, a chime sounds in a pattern of 5 sets of 5 beeps. If this occurs, diagnose and repair the airbag warning indicator and any SRS faults.
  1. Using a diagnostic scan tool, clear all Continuous Memory Diagnostic Trouble Codes (CMDTCs) from all modules.

    Pyrotechnic Device Disposal. General Procedures

    Disposal Disposal of Deployable Devices and Pyrotechnic Devices That Are Undeployed-Inoperative NOTE: All inoperative airbags, seatbelt pretensioners and inflatable seatbelt inflators have been placed on the Mandatory Return List...

    Battery Energy Control Module B (BECMB). Removal and Installation

    Removal   WARNING: The following procedure prescribes critical repair steps required for correct restraint system operation during a crash. Follow all notes and steps carefully...

    Other information:

    Ford Fusion 2013–2020 Service Manual: Information and Entertainment System - Component Location. Description and Operation


    NOTE: The available speaker configurations are shown first. The remaining hidden audio/SYNC system components and various cable routings follow the speaker configurations. NOTE: Some vehicles may not be equipped with all the optional components shown...

    Ford Fusion 2013–2020 Service Manual: Rear Floor Panel Crossmember. Removal and Installation


    Special Tool(s) / General Equipment Resistance Spotwelding Equipment 8 mm Drill Bit MIG/MAG Welding Equipment Spot Weld Drill Bit Locking Pliers Removal NOTICE: Battery electric vehicle (BEV), hybrid electric vehicle (HEV) and plug-in hybrid electric vehicle (PHEV) contain a high-voltage battery...

    Categories

    Cross Traffic Alert System Sensors

    Ford Fusion. Cross Traffic Alert System Sensors

    The sensors are behind the rear bumper on both sides of your vehicle.

    read more

    Copyright © 2024 www.fofusion2.com