Ford Fusion Manuals

Ford Fusion: Automatic Transmission External Controls - 6-Speed Automatic Transmission – 6F35 / Selector Lever Cable Adjustment - 1.5L EcoBoost (118kW/160PS) – I4. General Procedures

Adjustment

  1. Turn the ignition switch to the OFF position and apply the parking brake.
Ford Fusion. Selector Lever Cable Adjustment - 1.5L EcoBoost (118kW/160PS) – I4. General Procedures
  1. Using the diagnostic scan tool select the cable adjustment mode.
  1. NOTE: The GSM will alternate flashing D or N and S simultaneously.

    Choose D on the GSM.
Ford Fusion. Selector Lever Cable Adjustment - 1.5L EcoBoost (118kW/160PS) – I4. General Procedures
  1. Remove the air cleaner.
    Refer to: Air Cleaner (303-12A Intake Air Distribution and Filtering - 1.5L EcoBoost (118kW/160PS) – I4, Removal and Installation).
  1. Disconnect the selector lever cable from the transmission manual lever.
Ford Fusion. Selector Lever Cable Adjustment - 1.5L EcoBoost (118kW/160PS) – I4. General Procedures
  1. NOTE: Verify D is illuminated on the IPC.


    Position the manual control lever in D.
    1. Rotate the manual control lever counterclockwise until it stops.
    1. Rotate the manual control lever 3 detents into D.
Ford Fusion. Selector Lever Cable Adjustment - 1.5L EcoBoost (118kW/160PS) – I4. General Procedures

  1. Unlock the adjuster.
    1. Move the slide to the left.
    1. While holding the slide, position the adjuster lock upward.
Ford Fusion. Selector Lever Cable Adjustment - 1.5L EcoBoost (118kW/160PS) – I4. General Procedures
  1. Connect the selector lever cable to the transmission manual lever.
Ford Fusion. Selector Lever Cable Adjustment - 1.5L EcoBoost (118kW/160PS) – I4. General Procedures
  1. Snap the adjuster lock into place.
Ford Fusion. Selector Lever Cable Adjustment - 1.5L EcoBoost (118kW/160PS) – I4. General Procedures
  1. Choose P on the GSM.
Ford Fusion. Selector Lever Cable Adjustment - 1.5L EcoBoost (118kW/160PS) – I4. General Procedures
  1. Clear any DTCs.
  1. Shift the transmission through the ranges starting in P, then R, then N, then D, then N, then R and then back to P.
  1. Check for DTCs.
  1. Disconnect the scan tool.
  1. Install the air cleaner.
    Refer to: Air Cleaner (303-12A Intake Air Distribution and Filtering - 1.5L EcoBoost (118kW/160PS) – I4, Removal and Installation).
  1. Verify that the vehicle starts in P and N only and that the reverse lamps illuminate in R.

    Brake Shift Interlock Actuator Manual Override. General Procedures

    Activation NOTE: This vehicle is equipped with a brake shift interlock feature that prevents the vehicle from being moved out of P when the ignition is in the ON position until the brake pedal is applied...

    Brake Shift Interlock Override Switch. Removal and Installation

    Removal NOTE: Removal steps in this procedure may contain installation details. Open the floor console stowage bin lid. On both sides...

    Other information:

    Ford Fusion 2013–2020 Service Manual: Front Controls Interface Module (FCIM). Removal and Installation


    Special Tool(s) / General Equipment Interior Trim Remover Removal NOTE: Removal steps in this procedure may contain installation details. NOTE: If installing a new module, it is necessary to upload the module configuration information to the scan tool prior to removing the module...

    Ford Fusion 2013–2020 Service Manual: Evaporator Inlet and Outlet Manifold. Removal and Installation


    Removal NOTICE: During the removal or installation of components, cap, tape or otherwise appropriately protect all openings and tubes/fittings to prevent the ingress of dirt or other contamination. Remove caps, tape and other protective materials prior to installation...

    Categories

    Cross Traffic Alert System Sensors

    Ford Fusion. Cross Traffic Alert System Sensors

    The sensors are behind the rear bumper on both sides of your vehicle.

    read more

    Copyright © 2025 www.fofusion2.com