Ford Fusion Manuals

Ford Fusion: Multifunction Electronic Modules / Transport Mode Deactivation. General Procedures

Deactivation

NOTE: After vehicle build, some vehicle modules are set in Transport mode including the IPC and the BCM. Transport mode reduces battery drain during longer periods where the vehicle is not used. While in transport mode, the IPC displays TRANSPORT MODE CONTACT DEALER in the message center. Various systems may be altered or are disabled when in the transport mode. The vehicle automatically reverts to normal operation mode after being driven 120 km (75 mi). The vehicle can be manually taken out of Transport mode using this procedure.

If the IPC displays FACTORY MODE CONTACT DEALER in the message center the vehicle is set in factory mode. The system does not automatically revert to another mode and must be manually set to either the transport or normal operation mode. Refer to the Factory Mode Deactivation procedure in this section.
  1. Ford Fusion. Transport Mode Deactivation. General Procedures  WARNING: Before beginning any service procedure in this section, refer to Safety Warnings in section 100-00 General Information. Failure to follow this instruction may result in serious personal injury.

    Place the ignition in the OFF position.
  1. Verify the battery is fully charged.
    Refer to: Battery Charging (414-01 Battery, Mounting and Cables, General Procedures).
  1. Place the ignition in the ON position.
  1. NOTE: Steps 4 and 5 must be carried out within 10 seconds.

    Press and release the brake pedal 5 times.
  1. NOTE: The IPC message center indicates NORMAL MODE when the procedure has been successfully completed.

    Press and release the hazard switch 2 times.
  1. Start the engine.
  1. Place the ignition in the OFF position.
  1. Verify the RKE works correctly.

    Factory Mode Deactivation. General Procedures

    Deactivation NOTE: During vehicle build, some modules, such as the IPC and BCM module are set in factory mode. Factory mode reduces the drain on the battery during longer periods where the vehicle is not used...

    Body Control Module (BCM). Removal and Installation

    Special Tool(s) / General Equipment Interior Trim Remover Removal All vehicles NOTE: Removal steps in this procedure may contain installation details...

    Other information:

    Ford Fusion 2013–2020 Service Manual: Torque Converter Seal. Removal and Installation


    Special Tool(s) / General Equipment 307-003 (T57L-500-B) Holding Fixture, Transmission 307-091Handle, Torque ConverterTKIT-2009TC-F 307-566Retainer, Torque ConverterTKIT-2006C-FFMFLMTKIT-2006C-LMTKIT-2006C-ROW 307-625Fixture, Bench MountingTKIT-2008ET-FLMTKIT-2008ET-ROW 307-627Installer, Converter SealTKIT-2008ET-FLMTKIT-2008ET-ROW Puller Removal ..

    Ford Fusion 2013–2020 Service Manual: Timing Belt. Removal and Installation


    Special Tool(s) / General Equipment 303-1097Locking Tool, Variable Camshaft Timing Oil Control UnitTKIT-2010B-FLMTKIT-2010B-ROW 303-1550Alignment Tool, Crankshaft Vibration DamperTKIT-2012A-FLTKIT-2012A-ROW 303-393-02Adapter for 303-393TKIT-2012A-FLTKIT-2012A-ROW 303-393ALocking Tool, FlywheelTKIT-2012A-FLTKIT-2012A-ROW 303-748Locking Tool, CrankshaftTKIT-2010B-F..

    Categories

    Adjusting the Steering Wheel

    WARNING: Do not adjust the steering wheel when your vehicle is moving.

    Note: Make sure that you are sitting in the correct position.

    Ford Fusion. Adjusting the Steering Wheel

    Unlock the steering column. Adjust the steering wheel to the desired position.

    read more

    Copyright © 2022 www.fofusion2.com